[ROVERNET - UK] Dinitrol

[Slatskars]

Has anyone in the group used Finnegan's Waxol? this can be purchased through 
MOSS Motors in a kit form with a pump spray unit and plastic tubing for 
insertion into small spaces. My old standby, Texaco Rustproofing Compound, 
is no longer produced. Too bad it really worked in very aggressive rust 
prone areas. I tested it on Guam. Impossible to be more than three miles 
from the ocean.

Slats
----- Original Message ----- 
From: "James Dean" <jaguru at bellsouth.net>
To: <rovernet at lyris.ccdata.com>
Sent: Wednesday, November 09, 2005 10:15 PM
Subject: Re: [ROVERNET - UK] Dinitrol


> The only way to undercoat a P6 is to unbolt all the body panels, which is 
> not difficult. You then simply clean all panels, and undercoat the back 
> sides. Otherwise you will miss all the spots that really ned undercoating. 
> You can use Body Schutz, a 3M product, that takes a special applicator or 
> gun. Frankly, I think Good quality(Such as 3M) PAINTABLE undercoating in a 
> spray can  is just as good. A good cleaning agent before this, is cheap 
> wash-grade lacquer thinner($25 for 5  gallons)- Wipe it on with a wet rag, 
> Immediately wipe it off with a dry rag; use blue nitrile gloves, and 
> change them when they dissolve.Use a fan and plenty of 
> ventilation.Obviously this is a good time to replace all the rubber seals. 
> James Dean, Ft. Lauderdale.
> ----- Original Message ----- 
> From: "Ruotolo Gianluca (DD)" <gianluca.ruotolo at enel.it>
> To: <rovernet at lyris.ccdata.com>
> Sent: Wednesday, November 09, 2005 7:07 AM
> Subject: [ROVERNET - UK] Dinitrol
>
>
>
>
> Dear friends,
>
> as you know, Dinitrol is said to be one of the best
> protections against the rust. Now I'm restoring my P6 2000 TC and I
> wanto to apply dinitrol under the car and inside the doors. I remember
> there was an article on this subject in Classic Cars or in Classic and
> Sprots one or two years ago. Did someone read it? and does someone still
> have it? I'm not able to find that copy, but I need these informations.
>
> I bought it as a liquid warnish, and as you know there are two different
> kinds: black to paint under the car and white ( to put inside the doors
> and the boxes).
>
> What do I have to do? Do I have to heat it, or dilute it it before
> application?
> And with which products?
> Do I have to spray it in some way inside the doors?
> And, again, how many litres do I need for a p6?
> Do I need a speciial tool or a simple paint - brush could be enough?
>
> Excuse me but in Italy it's quite rare.
> At the end we are in a sunny country!
>
> Every indications will be appreciated.
>
> Best regards, thanks in advance, Gianluca.
>
> _______________________________________________
> rovernet mailing list
> rovernet at lyris.ccdata.com
> To unsubscribe, go to this web page, look near the bottom and follow 
> instructions:
> http://mailman.nipltd.com/mailman/listinfo/rovernet
>
> _______________________________________________
> rovernet mailing list
> rovernet at lyris.ccdata.com
> To unsubscribe, go to this web page, look near the bottom and follow 
> instructions:
> http://mailman.nipltd.com/mailman/listinfo/rovernet
>