Claire Re: [ROVERNET - UK] Update on an earlier problem
Kent Kinard
kkinard at wcc.net
Sat Jul 29 12:28:57 BST 2006
Glen, I need to check your medications again.
Kent K.
On Sat, 29 Jul 2006 01:01:28 -0400
Glen Wilson <rovercar at comcast.net> wrote:
> Alan Francis once told me that the spherical ball at the
>bottom of the gearshift lever was packed at Solihull with
>a small hedgehog or a similarly sized rodent to take up
>any play in the system and promote smooth operation of
>the moving parts. When Chris Devlin lived in San Diego,
>he preferred using a young prairie dog because they were
>much easier to source in California than hedgehogs. Dave
>Walker says that a suitably sized echidna works just fine
>Down Under.
>
> In a pinch, a somewhat obese hamster with a twist of
>Mallard will provide a temporary fix.
>
> I hope this has been helpful.
>
> Glen
>
> Glen Wilson
> http://stores.ebay.com/EasyAuctionServicesPA
> A bit of this, a bit of that...
>
>
>
> Gordon Harrower wrote:
>> Paul Smith wrote:
>>
>>> The base shouldn't move a lot, 1/8" is plenty.
>>> The bar locates on the gearbox vis a bush.
>>> I can scan the workshop manual page if desired.
>>>
>>> PVS
>>>
>>>
>>> ----- Original Message ----- From: "Gordon Harrower"
>>> <griffo at comcast.net>
>>> To: <rovernet at lyris.ccdata.com>
>>> Sent: Saturday, July 29, 2006 10:51 AM
>>> Subject: Re: [ROVERNET - UK] Update on an earlier
>>>problem
>>>
>>>
>>>
>>>
>>>> Paul Smith wrote:
>>>>
>>>>
>>>>>> I've now replaced the 4 rubber pads and the vaguely
>>>>>>triangular
>>>>>> one, as
>>>>>> well as the fabled "spherical seat." It now will go
>>>>>>into all
>>>>>> gears but
>>>>>> 3rd, running or not, and there still seems to be too
>>>>>>much play in the
>>>>>> gearshift mechanism. There's a bar that connects the
>>>>>>gearshift
>>>>>> mechanism to the transmission, and that bar seems loose,
>>>>>>but
>>>>>> difficult
>>>>>> to tighten.
>>>>>>
>>>>>>
>>>>>>
>>>>> 1. Is the bar broken?
>>>>> 2. Is it loose on the base unit (it is meant to have
>>>>>movement
>>>>> there), or
>>>>> loose on the gearbox?
>>>>>
>>>>> Can you organise an assistant to operate the gear lever
>>>>>whilst you
>>>>> watch
>>>>>
>>> the
>>>
>>>
>>>>> selector arm?
>>>>>
>>>>> PVS
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> rovernet mailing list
>>>>> rovernet at lyris.ccdata.com
>>>>> To unsubscribe, go to this web page, look near the
>>>>>bottom and follow
>>>>>
>>> instructions:
>>>
>>>
>>>>> http://mailman.nipltd.com/mailman/listinfo/rovernet
>>>>> Back-up list and photos at:
>>>>> http://autos.groups.yahoo.com/group/Rover_net/
>>>>>
>>>>>
>>>>>
>>>>>
>>>> Paul,
>>>>
>>>> It's loose on both ends. I'm not sure how to tighten it
>>>>on the gearbox
>>>> end. Meanwhile, the whole rectangular base for the
>>>>gearshift moves
>>>> around quite a bit. It's one of those things I never
>>>>looked at when
>>>> things were going well, so it's hard to tell what's
>>>>normal. Thanks,
>>>>
>>> Gordon.
>>>
>>>
>>>> _______________________________________________
>>>> rovernet mailing list
>>>> rovernet at lyris.ccdata.com
>>>> To unsubscribe, go to this web page, look near the
>>>>bottom and follow
>>>>
>>> instructions:
>>>
>>>
>>>> http://mailman.nipltd.com/mailman/listinfo/rovernet
>>>> Back-up list and photos at:
>>>> http://autos.groups.yahoo.com/group/Rover_net/
>>>>
>>>>
>>>> --
>>>> No virus found in this incoming message.
>>>> Checked by AVG Free Edition.
>>>> Version: 7.1.394 / Virus Database: 268.10.4/402 -
>>>>Release Date:
>>>> 27/07/2006
>>>>
>>>>
>>>>
>>>
>>>
>>> _______________________________________________
>>> rovernet mailing list
>>> rovernet at lyris.ccdata.com
>>> To unsubscribe, go to this web page, look near the
>>>bottom and follow
>>> instructions:
>>> http://mailman.nipltd.com/mailman/listinfo/rovernet
>>> Back-up list and photos at:
>>> http://autos.groups.yahoo.com/group/Rover_net/
>>>
>>>
>>>
>> Paul,
>>
>> I've got the manual, thanks. I'll bet the bush has
>>deteriorated,
>> because it seems pretty loose. I'll have to take a
>>closer look
>> tomorrow, and I'll let you know. My concern is how
>>accessible it is,
>> or if I'll have to drop the gearbox to get at it.
>> Thanks, Gordon.
>>
>> _______________________________________________
>> rovernet mailing list
>> rovernet at lyris.ccdata.com
>> To unsubscribe, go to this web page, look near the
>>bottom and follow
>> instructions:
>> http://mailman.nipltd.com/mailman/listinfo/rovernet
>> Back-up list and photos at:
>> http://autos.groups.yahoo.com/group/Rover_net/
>>
>
> _______________________________________________
> rovernet mailing list
> rovernet at lyris.ccdata.com
> To unsubscribe, go to this web page, look near the
>bottom and follow instructions:
> http://mailman.nipltd.com/mailman/listinfo/rovernet
> Back-up list and photos at:
> http://autos.groups.yahoo.com/group/Rover_net/
More information about the rovernet
mailing list