[ROVERNET - UK] uns*bscribe
Andrew H. Litkowiak
andylit at runbox.com
Mon May 15 13:51:05 BST 2006
Very painful. Not too many make it through the process.
David Read wrote:
> Andrew !!!!!
> You forgot to mention that re-subcribing is the reverse of the above.
>
> :-)
>
> Dave
> South Oz
>
> Andrew H. Litkowiak wrote:
>
>> Peter Mitchell wrote:
>>
>>> Hi Eric,
>>>
>>> I am going off the net for a week or two for pc repair / upgrade, please
>>> unsubscribe me for the present.
>>>
>>> Kind regards
>>
>>
>> Here is how to unsubscribe:
>>
>> First, e-mail rovernet-request and ask for an Unsubscribing Kit. Then
>> follow these simple directions.
>>
>> The kit is the standard no-fault type. Depending on requirements,
>> System A and/or System B can be used. When operating System A, depress
>> lever and a plastic dalkron unsubscriber will be dispensed through the
>> slot immediately underneath. When you have fastened the adhesive lip,
>> attach connection marked by the large "X" outlet hose. Twist the
>> silver- colored ring one inch below the connection point until you
>> feel it lock.
>>
>> The kit is now ready for use. The unsubscriber is activated by the
>> small switch on the lip. When securing, twist the ring back to its
>> initial condition, so that the two orange lines meet. Disconnect.
>> Place the dalkron unsubscriber in the vacuum receptacle to the rear.
>> Activate by pressing the blue button.
>>
>> The controls for System B are located on the opposite side. The red
>> release switch places the unsubscriber into position; it can be
>> adjusted manually up or down by pressing the blue manual release
>> button. The opening is self-adjusting. To secure after use, press the
>> green button, which simultaneously activates the evaporator and
>> returns the unsubscriber to its storage position.
>>
>> You may log off if the green exit light is on over the evaporator. If
>> the red light is illuminated, one of the unsubscriber requirements has
>> not been properly implemented. Press the "List Admin" call button on
>> the right of the evaporator. I will secure all facilities from my
>> control panel.
>>
>> To use the Auto-Unsub, first undress and place all your clothes in the
>> clothes rack. Put on the Velcro slippers located in the cabinet
>> immediately below. Enter the Con-tainer, taking the entire kit with
>> you. On the control panel to your upper right upon entering you will
>> see a "Con-tainer seal" button. Press to activate. A green light will
>> then be illuminated immediately below. On the intensity knob, select
>> the desired setting. Now depress the Auto-Unsub activation lever. Act
>> normally.
>>
>> The Auto-Unsub will automatically go off after three minutes unless
>> you activate the "Manual off" override switch by flipping it up. When
>> you are ready to leave, press the blue "Con-tainer seal" release
>> button. The door will open and you may leave. Please remove the Velcro
>> slippers and place them in their receptacle.
>>
>> If you prefer the ultrasonic log-off mode, press the indicated blue
>> button. When the twin panels open, pull forward by rings A & B. The
>> knob to the left, just below the blue light, has three settings, low,
>> medium or high. For normal use, the medium setting is suggested. After
>> these settings have been made, you can activate the device by
>> switching to the "ON" position the clearly marked red switch. If
>> during the Unsubscribing operation, you wish to change the settings,
>> place the "manual off" override switch in the "OFF" position. You may
>> now make the change and repeat the cycle. When the green exit light
>> goes on, you may log off and have lunch. Please close the door behind
>> you. Don't forget to dressb efore leaving the room.
>
>
> <snip>
>
> _______________________________________________
> rovernet mailing list
> rovernet at lyris.ccdata.com
> To unsubscribe, go to this web page, look near the bottom and follow
> instructions:
> http://mailman.nipltd.com/mailman/listinfo/rovernet
> Back-up list and photos at:
> http://autos.groups.yahoo.com/group/Rover_net/
>
>
>
More information about the rovernet
mailing list