[ROVERNET - UK] Re: rovernet Digest, Vol 50, Issue 8

David Walter david at davidwalter.net
Sun Jan 7 17:32:16 GMT 2007


Hi Geff,

The clock should work if you have it wired correctly, try reinstalling 
it and see if it then works.

1 minute a week is pretty good for these clocks, they are 
electro-mechanical not quartz and there is no temperature compensation 
either.
At 1 minute a week I would leave it alone.

They can be repaired I have overhauled, cleaned and bushed many of them 
in the past.
They do wear badly, especially in the bearings after 30+ years, imagine 
what the engine would be like if it ran non stop for that long.

You have to decide if its worth overhauling the clock, the only choices 
are, overhaul it, do nothing, or attempt to replace it.
It seems to me keeping your car original is always a worthwhile 
proposition.

As for buying a replacement clock, it will have come from a scrapped 
Rover and is more than likely just as bad if not worse condition, the 
statement that "it runs" is meaningless and will give no clue as to its 
real mechanical condition

The Kienzle clock was a  very successful clock movement used from 1962 
until 1977 when it was replaced by quartz, many makers in UK and Europe 
used the Kienzle  movement with different dials and housings.
In UK the Kienzle replaced the Smiths car clock which was truly a piece 
of junk, it ran badly and is unrepairable.

David


----- Original Message ----- 
From: <rovernet-request at lyris.ccdata.com>
To: <rovernet at lyris.ccdata.com>
Sent: Sunday, January 07, 2007 4:00 AM
Subject: rovernet Digest, Vol 50, Issue 8


> Send rovernet mailing list submissions to
> rovernet at lyris.ccdata.com
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://mailman.nipltd.com/mailman/listinfo/rovernet
> or, via email, send a message with subject or body 'help' to
> rovernet-request at lyris.ccdata.com
>
> You can reach the person managing the list at
> rovernet-owner at lyris.ccdata.com
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of rovernet digest..."
>
>
> [ROVERNET-UK]
>
> Today's Topics:
>
>   1.  Kienzle clock regulation (geffandjulie)
>   2. Re:  Kienzle clock regulation (Tomas B?rjeson)
>   3. Re:  Kienzle clock regulation (Paul Smith)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Sat, 6 Jan 2007 13:01:59 -0800
> From: "geffandjulie" <geffandjulie at comcast.net>
> Subject: [ROVERNET - UK] Kienzle clock regulation
> To: "Rovernet05" <rovernet at lyris.ccdata.com>
> Message-ID: <010601c731d5$e8f390e0$db901418 at geofferywvo1hq>
> Content-Type: text/plain; format=flowed; charset="iso-8859-1";
> reply-type=original
>
> My clock works in the car but loses minutes a week. I have the 
> instrument
> binnacle out, and have hooked up 12V DC to the male connector and case
> ground. I measure 14v across, yet the clock seems not to work. I have 
> hooked
> up a spare clock in parallel, and it also does not work, tho' I cannot
> verify that it worked before.Ideas please.
> Also, is it worth 'overhauling' these old clocks?  Nobody here in 
> Portland
> OR has the capabilities, I think.
> Geff and Julie McCarthy
> AvMedSafe
> 503-241-8468
>
>
>
>
> ------------------------------
>
> Message: 2
> Date: Sat, 06 Jan 2007 23:52:52 +0100
> From: Tomas B?rjeson <tmastaff at tripnet.se>
> Subject: Re: [ROVERNET - UK] Kienzle clock regulation
> To: rovernet at lyris.ccdata.com
> Message-ID: <7.0.1.0.2.20070106234133.04958a20 at tripnet.se>
> Content-Type: text/plain; charset="iso-8859-1"; format=flowed
>
> Hi
> These clocks are mechanical clocks with electric
> winding of the spring. It's usually this
> mechanism (or the spring) that breaks if they do
> not work. It is possible to repair them (I've
> done it) but if you can't do it yourself it may
> be difficult to find someone who is willing to
> try. There is a +/- adjustment on them but I
> don't think you can expect much greater accuracy
> then about a minute a week or so at best,
> especially after a quarter century or more. It's
> not a modern quartz crystal controlled electronic
> movement. You could always insert a modern
> movement in the old casing. You'll lose the intermittent "tick" 
> however.
>
> Tomas Börjeson
> Gothenburg, SWEDEN
> 1975 Rover 2200 TC Almond Yellow
> 1972 Rover 3500 V8 Cameron Green
> 1999 Rover 75 Connoisseur
>
>
> At 07:30 2007-01-07, you wrote:
>>My clock works in the car but loses minutes a
>>week. I have the instrument binnacle out, and
>>have hooked up 12V DC to the male connector and
>>case ground. I measure 14v across, yet the clock
>>seems not to work. I have hooked up a spare
>>clock in parallel, and it also does not work,
>>tho' I cannot verify that it worked before.Ideas please.
>>Also, is it worth 'overhauling' these old
>>clocks?  Nobody here in Portland OR has the capabilities, I think.
>>Geff and Julie McCarthy
>>AvMedSafe
>>503-241-8468
>>
>>_______________________________________________
>>rovernet mailing list
>>rovernet at lyris.ccdata.com
>>To unsubscribe, go to this web page, look near
>>the bottom and follow instructions:
>>http://mailman.nipltd.com/mailman/listinfo/rovernet
>>Back-up list and photos at:
>>http://autos.groups.yahoo.com/group/Rover_net/
>>
>
>
>
>
> ------------------------------
>
> Message: 3
> Date: Sun, 7 Jan 2007 14:51:03 +1100
> From: "Paul Smith" <vmitps at netspace.net.au>
> Subject: Re: [ROVERNET - UK] Kienzle clock regulation
> To: <rovernet at lyris.ccdata.com>
> Message-ID: <015701c7320f$28ca18e0$0601010a at Skaterscomp2>
> Content-Type: text/plain; charset="iso-8859-1"
>
> How was the clock sitting when you were testing?
> They are sensitive to the angle.
>
> ----- Original Message ----- 
> From: "geffandjulie" <geffandjulie at comcast.net>
> To: "Rovernet05" <rovernet at lyris.ccdata.com>
> Sent: Sunday, January 07, 2007 8:01 AM
> Subject: [ROVERNET - UK] Kienzle clock regulation
>
>
>> My clock works in the car but loses minutes a week. I have the 
>> instrument
>> binnacle out, and have hooked up 12V DC to the male connector and 
>> case
>> ground. I measure 14v across, yet the clock seems not to work. I have
> hooked
>> up a spare clock in parallel, and it also does not work, tho' I 
>> cannot
>> verify that it worked before.Ideas please.
>> Also, is it worth 'overhauling' these old clocks?  Nobody here in 
>> Portland
>> OR has the capabilities, I think.
>> Geff and Julie McCarthy
>> AvMedSafe
>> 503-241-8468
>>
>>
>> _______________________________________________
>> rovernet mailing list
>> rovernet at lyris.ccdata.com
>> To unsubscribe, go to this web page, look near the bottom and follow
> instructions:
>> http://mailman.nipltd.com/mailman/listinfo/rovernet
>> Back-up list and photos at:
>> http://autos.groups.yahoo.com/group/Rover_net/
>>
>>
>> -- 
>> No virus found in this incoming message.
>> Checked by AVG Free Edition.
>> Version: 7.5.432 / Virus Database: 268.16.7/618 - Release Date: 
>> 6/01/2007
> 7:47 PM
>>
>>
>
>
>
> ------------------------------
>
> _______________________________________________
> rovernet mailing list
> rovernet at lyris.ccdata.com
> To unsubscribe, go to this web page, scroll to the bottom, and follow 
> instructions:
> http://mailman.nipltd.com/mailman/listinfo/rovernet
> Back-up list and photos at:
> http://autos.groups.yahoo.com/group/Rover_net/
>
> End of rovernet Digest, Vol 50, Issue 8
> *************************************** 




More information about the rovernet mailing list